'88 E30
-
What's the weight on the JB?
I think 13lbs
@DrLeadFoot
-
No progress really, just put the pan on after getting a new pickup tube gasket. Also put some ngk plugs in it.
Just need to swap the harness from the m50 to the s50. Clean up intake manifold & put new gaskets in it. Clean up TB. Random vacuum line from fpr to intake. Random coolant line to bypass TB.
Then all the driveline/clutch stuff
Oh and a serp belt
How it sits now. I bet the white gets dirty before I even put fluids in it
Do have a question: I've read that you need to run shorter bolts to hold the crank pulley on after removing the ac pulley. Some say they ran shorter, others did not. I cannot see anything touching something it shouldn't. For piece of mind I'll probably just get shorter bolts
-
Where does the small tube go? Pic of line to ICV?
You could tap the valve cover with a 3/4" NPT tap and run braided lines to a catch can.
@DrLeadFoot
-
The small tube plugs into the ICV hose that curls up into the intake manifold
-
-
Small tube from PCV
goes to this little nipple close to the white gasket (top of pic) on the ICV hose which goes into the intake manifold 
Large tube has those barbed connectors on the dipstick tube it can be connected to. Or I could just run it to a catch can. Instead of having it drain everywhere
-
Also installed the UHMW PS delete from condor because I was bored
Ultra high molecular weight vs aluminum.
Green jacket, gold jacket, who gives a shit
-
I blocked the small hose as it doesn't really do much and will be running the large hose into a catch can, but the large one is currently vented to atmosphere.
I needed shorter bolts in the timing wheel, but ended up turning the pulley into a spacer instead. -
Also installed the UHMW PS delete from condor because I was bored
I saw my delrin oops, so I fixed it
Thx bb
-
I blocked the small hose as it doesn't really do much and will be running the large hose into a catch can, but the large one is currently vented to atmosphere.
I needed shorter bolts in the timing wheel, but ended up turning the pulley into a spacer instead.
Assuming you also blocked the nipple on the ICV hose?
I'm gonna probably order shorter bolts then. I don't want to put the pulley back on
-
I am using that one for boost related things, so it works out well for me! In your case you should block it off.
Yeah, shorter bolts will do the trick. I cut off the pulley portion so I just had the flat disc, instead of getting shorter bolts.
-
I am using that one for boost related things, so it works out well for me! In your case you should block it off.
Yeah, shorter bolts will do the trick. I cut off the pulley portion so I just had the flat disc, instead of getting shorter bolts.
Any purpose to blocking off the small line other than simplifying crap/not letting oil get everywhere
-
On the valve cover side, not really. On the ICV side it is open to the intake so it would result in a vacuum leak if left unplugged.
-
On the valve cover side, not really. On the ICV side it is open to the intake so it would result in a vacuum leak if left unplugged.
I get the vacuum leak part. But why plug everything up? Why not just connect everything with new line?
I'm just curious
-
Personal preference I guess. I don't think that tiny line is doing too much. Especially if you are just VTA
-
On obd1 the large line goes to the intake elbow before the throttle body. Obd2 it goes to the cyclone cannister thing and then to the dipstick tube. You could put a catch can between if you dislike oil in your intake manifold. I just giver, more lubrication hurts nothing.
Sent from my potato phone
-
On obd1 the large line goes to the intake elbow before the throttle body. Obd2 it goes to the cyclone cannister thing and then to the dipstick tube. You could put a catch can between if you dislike oil in your intake manifold. I just giver, more lubrication hurts nothing.
Sent from my potato phone
If there isn't a vacuum issue with them being unplugged I'd rather not get oil everywhere. I've ran out of harbor freight rags as is.
-
Added oil & put a new belt on.
I still need shorter bolts for the crank pulley, I just wanted to see if the belt was correct. It was.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login