The One That Didn't Get Away [100K Mile E30 325is]
-
Can't wait to check this out in person. Excited to see where both of your E30s take you.
-
Congrats on this wonderful addition!
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
BaT bound
-
BaT bound
Definitely thought about it, but not sure I will see another in this good of condition for the price.
-
Definitely thought about it, but not sure I will see another in this good of condition for the price.
Few days in and you’re already attached. RIP
-
Few days in and you’re already attached. RIP
I've wanted an (running and driving)E30 for quite some time.
-
I've wanted an (running and driving)E30 for quite some time.
This is how it starts
-
Cleaning/detailing has begun.
Rented a carpet cleaner to take care of the gross carpet. Initial thought of mold/mildew was incorrect(thankfully). Think someone spilled something on the carpet/just dirty in general. Shop doesn't have hot water right now, so I snagged some near boiling hot water from the Kwik Trip just down the road. Carpet look pretty good minus a couple spots that are still dirty a bit. But, I have new floor mats that will cover most of the still problem areas. Water that came out of the machine was pure brown.
With the seats out, did a full leather conditioning. I really like the Griots Garage products so I chose their Leather Care. I'm sure theres other possible better options out there, but for how readily available their products are and how well it performs, I really like them. Returned some good shine, leather feels supple, and took care of the dry cracking areas. Pulled the steering wheel cover off and did the same. Mtech 1 is in great condition.
I washed and claybared the whole car this afternoon. Decent enough day for it, fair amount of overcast so not a ton of direct sunlight. I'm partial to Meguiars products for exterior detailing. Again, possible better stuff out there, but for my level of detailing and intended outcome, fits the bill.
Wanted to see what I could do about the paint. Good news is that I think it will come back great, just a lot of time needs to be spent doing so. Started on the trunk to just get an idea of what I was getting into. Meguiars Ultimate Compound and medium grade pad on my rotary wheel. First picture below was just my first initial pass to get an idea of cut amount and wheel speed. This red is kind of hard to photograph.
Pretty big difference right away.
After the compound pass.
After using the Meguiars Ultimate Polish. Decent, but could be better. Might try a coarser pad for the compound and some more speed to get some more cut. Trunk, roof, and hood are always the most difficult.
And then just a pass of the Ultimate Wax. You can see the difference between the trunk and the quarter.
Parked in the shop.
More work tomorrow, maybe can finish the whole car. Don't think I'll cut the front quarters or hood as it was repainted. I'll just do a light polish on it.
Should I put the smoked smileys on this car or leave the ellipsoids?
-
Stock headlights until it sees aftermarket wheels
More paint correction. Found that compound was a little too abrasive for the sides as I faded a couple inches of my pinstripe on the driver side. Went with just the polish and it brought back the paint to level I was satisfied with. Single stage old paint is difficult to work with and I'm not comfortable pushing further for that extra 10% I want to achieve without possible wrecking the paint. New cars are much easier to work with paint wise.
Before look at the rear quarter:
After polishing:
Better, but as you can see, could be better. I don't know if this is just the quality of the paint or if I might need to go at it with a finer grain pad and some more speed.
I have used a rotary buffing wheel for the longest time. I bought a rotary for personal use after I stopped detailing cars for Bergstrom because it was what I was used to. They are not as forgiving and do not have any safety features built in. I bought a 6 inch DA from Harbor Freight during their parking lot sale today. For $60, this is really all you need to get good results from paint correcting. 8mm of travel, edge safety feature, and 2" smaller surface than my rotary are much better for my use.
I got the roof, driver side rear quarter and door done today, shit takes a long time.
Pictures out side.
-
@B C this paint is really difficult to take pictures of.
So. Whens the S52 swap coming? I have one for sale
Clean S52 swapped E30s are pulling some hella numbers. Ask
@wasnt m3
-
So. Whens the S52 swap coming? I have one for sale
Clean S52 swapped E30s are pulling some hella numbers. Ask
@wasnt m3
This is going to stay M20 for the foreseeable future.
Coming along nicely! You can always use some 1/4" tape to protect the stripe. If you want the stripe gone, oven cleaner works well without damaging the original paint of the car.
Was considering covering it, but would have been a huge pain to cut down a bunch of large painters tape to cover. I love the stripe.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login