‘91 E30
-
The one time I actually make it into town...
And PB1 is “too far away” to come hang out... unreal
-
The one time I actually make it into town...
You should hang out more when I invite you places...
-
Bummerworld 3” arrived. TMS shorty headers get here Saturday
-
ECS at it again
-
They sent you one header?!?
Yep, 3 cyl conversion - I hope it saved them money on shipping lol
-
Fill it with dildos and send it back.
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
Fill it with dildos and send it back.
The other half is supposed to arrive today. Will update on if it’s the correct one lol
-
ECS is the butt of a lot of jokes usually, but ordering through @patsbimmer1 is the way to do it. He had the second piece overnighted and I didn’t have to deal with any mouthbreathers. If you need to order through ECS, hit up Pat.
-
ECS is the butt of a lot of jokes usually, but ordering through @patsbimmer1 is the way to do it. He had the second piece overnighted and I didn’t have to deal with any mouthbreathers. If you need to order through ECS, hit up Pat.
No Dillys needed!
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
ECS is the butt of a lot of jokes usually, but ordering through @patsbimmer1 is the way to do it. He had the second piece overnighted and I didn’t have to deal with any mouthbreathers. If you need to order through ECS, hit up Pat.
Pat IS a live saver. He is the only reason I order from ECS
-
Went to the shop. Tapped some holes. Tossed headers on. Check the ICV hoses for cracks, found some. Front lift point is all fucked so I went home. I’ll check back in a month
-
-
How hard do you suppose those shorties would be to install in a car. Do the primaries block studs?
I’ll get some better pics for you
-
Got sent the wrong TOB. Ruined some stuff on the trans. Slow progress
-
Headers are on
By far the easiest set of aftermarket headers I’ve ever installed on these motors. Room to get to every nut/stud from the top side
-
Also needed to fix the lift point. The top most bolt hole for the lift bracket was all blown apart. I wanted to just re tap the remaining area, but I Was not able to get a tap through whatever material that threaded portion was. Could barely drill it out to the right size.
Decided to buy a stud and just jb weld the cock sucker in because it only needs to work one more time anyways. Had to re tap that lower lifting bracket bolt hole as well because the threads were junk.
Also got a rethreaded brown temp sensor so the dash temp gauge will work. Had to chase those threads as well. I’m getting very familiar with my tap set lately.
Correct TOB and new reverse switch hopefully get here Saturday, so I can get the trans tossed on.
-
Oh and swapped out the pilot bearings for the larger one to accommodate the zf. In case anyone is curious about your shaft size I have included a pic of the difference
side note: 20ftlbs always seems like next to nothing for the pressure plate bolts
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login